Buna-N nitrile tri clamp gasket
40MPU-100-FDA

Tri-Clamp Buna-N Gasket (Nitrile Rubber)

$1.25IN STOCK
Ships in 1 business day
7 sizes, $1.15 to $22.00
SELECT SIZE

ABOUT THIS PART

Buna-N nitrile tri clamp gasket, FDA compliant and 3-A approved, in 1, 1.5, 2, 3, 4, 6 and 10 inch, from $1.15. Every size is priced on this page.

SPECIFICATIONS

MaterialBuna-N nitrile rubber
ComplianceFDA compliant, 3-A approved
ConnectionTri-clamp sanitary
Sizes1 in, 1.5 in, 2 in, 3 in, 4 in, 6 in, 10 in
Temperature range-30 F to 250 F (-34 C to 121 C)
Solvent compatibilityExcellent on butane, propane, heptane, hexane and pentane, with pentane per Cole-Parmer. Fair on ethanol, not for continuous use. Good (B) on isopropyl, per Cole-Parmer
Best forWater, food and general sanitary duty
For hydrocarbon serviceUse Viton, which rates excellent where Buna-N does not
Minimum solvent temperature, N.B. Oler system-40 F (-40 C) on standard elastomeric gaskets, -65 F (-54 C) with PTFE
Cold-side limitBuna-N stops at -30 F (-34 C), short of the -40 F (-40 C) minimum solvent temperature, so the gasket governs on the cold end rather than the vessel
What we recommend instead for solventViton as the default, and it is what we run in our own shop. The PTFE envelope gasket with a Viton filler, also sold as PTFE encapsulated Viton, for the coldest work or joints broken every run
Clamp torque30 in-lb, elastomeric gasket
Service intervalEvery 3 to 6 months
Quantity, 20 LB system22 six inch gaskets
Quantity, 40 LB system44 six inch gaskets
Built or stockedStocked in Bend, ships in 1 business day

Buna-N is the right gasket for water, food and general sanitary duty, and the cheapest in the range. For hydrocarbon extraction it is not the one to reach for.

Sizes and price

Size Price
1 in $1.25
1.5 in $1.15
2 in $2.50
3 in $3.25
4 in $5.50
6 in $13.50
10 in $22.00

The numbers

  • Temperature: -30 F to 250 F (-34 C to 121 C), the narrowest range of any gasket on this site
  • Clamp torque: 30 in-lb, the elastomeric figure. PTFE takes 50
  • Compliance: FDA compliant, 3-A approved
  • Excellent on: butane, propane, heptane, hexane, pentane
  • Fair on ethanol, not for continuous use. Good on isopropyl, with minor effect, per Cole-Parmer chemical resistance data

Which material for which job

Material Temperature Torque Pick it when
Buna-N -30 F to 250 F (-34 C to 121 C) 30 in-lb Water, food, general sanitary. Cheapest
Viton (FKM) -40 F to 400 F (-40 C to 204 C) 30 in-lb The hydrocarbon default, including isopropyl
PTFE envelope, Viton core -100 F to 400 F (-73 C to 204 C) 50 in-lb Cold service, or a joint broken every run

Buna-N will physically fit any tri-clamp joint on a 10, 20 or 40 LB system. Viton rates excellent on everything Buna-N does not, which is why it is the material we run on solvent.

The cold end, and what actually limits it

Minimum solvent temperature on an N.B. Oler system is -40 F (-40 C) on standard elastomeric gaskets, and -65 F (-54 C) with PTFE. Buna-N stops at -30 F (-34 C), which is short of both, so on the cold end the gasket is the limiting component rather than the vessel. Check the gasket against your lowest process temperature rather than against the vessel rating.

What we recommend

  • First choice for most buyers: the PTFE envelope gasket with a Viton filler, also sold as PTFE encapsulated Viton. PTFE chemistry against the process, including isopropyl, with a Viton core that springs back so the joint reseals instead of taking a set.
  • Default on a hydrocarbon system: Viton, rated -40 F to 400 F (-40 C to 204 C). Note that -40 F and -40 C are the same temperature, which is why both units read -40.
  • Viton is what we run in our own shop, and in our own operating experience it gives the best results in cold service of the elastomers we have used. That is shop experience rather than a laboratory result, and the published rating is still -40 F (-40 C).

Replacement and quantities

  • Replace every 3 to 6 months regardless of how it looks
  • Replace immediately on any cracking, tearing, splitting or permanent deformation
  • A gasket that has taken a compression set passes a cold leak check and then weeps once the line comes up to pressure. That is why interval beats inspection on a gasket
  • A 20 LB system takes 22 six inch gaskets. A 40 LB takes 44
  • Full comparison: Choosing the right gasket material for tri-clamp connections

Stocked in Bend, Oregon. Ships in 1 business day.

STOCKED, NOT BUILTStocked by N.B. Oler and built by its manufacturer.
FITSAny tri-clamp joint on water, food or general sanitary duty, sized to the joint, in 1, 1.5, 2, 3, 4, 6 and 10 inch. It will physically fit any tri-clamp joint on a 10, 20 or 40 LB system, but for hydrocarbon extraction Viton is the correct material: Buna-N rates only fair on ethanol and good (B) on isopropyl per Cole-Parmer. Not for service below -30 F (-34 C). Torque to 30 in-lb, not the 50 in-lb a rigid PTFE gasket takes.

▦ IN YOUR MANUAL

This part appears in the operator manual that ships with your system. The QR code there links to this page.

◈ REFERENCE FOR THIS PART

Choosing the Right Gasket Material for Tri-Clamp Connections →
Buna-N, Viton and PTFE compared on temperature, chemical compatibility and cost
Chemical Compatibility: Seals, Gaskets and Stainless →
Buna-N rates A on butane and propane but C on ethanol, and it is out of range at the cold end
Tri-Clamp Pressure Ratings by Clamp Style and Size →
These are the joint ratings Buna-N gaskets were hydrostatically tested with
Sintered Filter Technical Specifications →
The chemical compatibility table this page draws from
A Real-World Look at Butane Vapor Dynamics →
What the vapor side is doing, and the pressures your gaskets have to hold

COMMON QUESTIONS

Buna-N or Viton for extraction?

Viton. Buna-N rates only fair on ethanol and good (B) on isopropyl per Cole-Parmer. Viton rates excellent on all the hydrocarbons you run. Buna-N is cheaper and is the right call for water, food and general sanitary duty.

How often should tri-clamp gaskets be replaced?

Every 3 to 6 months in normal service. A gasket that has taken a compression set passes a leak check cold and then weeps once the line comes up to pressure, which is why interval beats inspection.

How many does a system take?

A 20 LB system takes 22 six inch gaskets and a 40 LB takes 44.

What temperature can Buna-N take?

-30 F to 250 F, which is -34 C to 121 C. That is the narrowest range of any gasket on this site.

Is Buna-N cold enough for my system?

Not quite. Minimum solvent temperature on an N.B. Oler system is -40 F (-40 C) on standard elastomeric gaskets, and Buna-N stops at -30 F (-34 C), so it is short by 10 F. Use Viton, which is rated to -40 F (-40 C) and is what we run in our own shop, or the PTFE envelope gasket with a Viton filler for the coldest work.

Which gasket should I use on solvent?

Viton is the default on a hydrocarbon system and the one we run. For the coldest work, or a joint broken every run, use the PTFE envelope gasket with a Viton filler, also sold as PTFE encapsulated Viton: PTFE chemistry against the process, including isopropyl, and a Viton core that springs back so the joint reseals. Buna-N is for water, food and general sanitary duty.

What torque?

30 in-lb, the elastomeric figure. PTFE takes 50. Torquing an elastomeric gasket to the rigid spec crushes it.

Is it food safe?

Yes, FDA compliant and 3-A approved.

What sizes do you carry?

1, 1.5, 2, 3, 4, 6 and 10 inch, every size priced on this page.