Skip to product information
1 of 1

Superlok

Superlok 3/8" Check Valve SHCV2-S-6, 1 psi and 100 psi Cracking

Superlok 3/8" Check Valve SHCV2-S-6, 1 psi and 100 psi Cracking

Regular price $59.95 USD
Regular price $65.00 USD Sale price $59.95 USD
Sale Sold out
Taxes included. Shipping calculated at checkout.
Cracking pressure
Quantity

Superlok SHCV2 series poppet check valve, 3/8 inch tube fitting both ends, 316 stainless, spring-loaded poppet, straight-through flow path. Two fixed cracking pressures on this page, 1 psi (0.07 bar) and 100 psi (6.9 bar). $59.95 each, either one.

Both are 6,000 psig (413 bar) maximum working pressure with a Cv of 1.8. Same valve, same body, same seals. The only difference between them is the spring, and the spring is the whole decision.

Final stock, not being restocked. These came off our own shelf and there is no reorder behind them. When they are gone this listing goes with them. Priced below every distributor listing we could find in October 2026, where the same two part numbers were $62.99 each against a $81.38 published regular price.

Which cracking pressure

Set point Part number Use it when
1 psi (0.07 bar) SHCV2-S-6-1P You want flow to start almost immediately and you only need the valve to stop reverse flow. Vapor paths, vent lines, pump discharge, anywhere a stiff spring would cost you flow you cannot spare.
100 psi (6.9 bar) SHCV2-S-6-100P The valve has to stay firmly shut until the system is genuinely up to pressure. Wrong anywhere you want flow to start early or on a low-pressure vapor path.

Put a 1 psi valve in a 100 psi position and it will pass when you did not want it to. Put a 100 psi valve in a 1 psi position and it will not open when you need it to. Read the number on the part you are replacing, not the picture. If you want something in between, Superlok publishes 5, 10 and 25 psi (0.34, 0.68 and 1.7 bar) springs in this same series, and we stock the Swagelok SS-CHS6-25 at 25 psig (1.8 bar) in the same 3/8 inch size.

Specifications, from the Superlok SHCV series catalog

Series SHCV2
Part numbers on this page SHCV2-S-6-1P and SHCV2-S-6-100P
Tube size 3/8 in. tube OD, Superlok tube fitting both ends
Cracking pressure Fixed, not adjustable. 1 psi (0.07 bar) or 100 psi (6.9 bar)
Maximum working pressure 6,000 psig (413 bar), SHCV2 with tube fitting ends
Cv 1.8
Inlet and outlet body 316 stainless
Poppet Viton bonded to 316 stainless
Poppet stopper 316 stainless
Spring 304 stainless
O-ring, standard Viton, fluorocarbon FKM
Backup ring PTFE
Temperature range, FKM seal -10 F to 375 F (-23 C to 190 C)
Minimum reseal pressure, 1 psi version 5 psig (0.34 bar), per Superlok's part data for SHCV2-S-6-1P
Mechanism Spring-loaded poppet, straight-through flow path, one way
Availability Clearance, final stock, not being restocked
Price $59.95 each, either set point

What the part number says

SHCV2-S-6-100P reads left to right as series, end connection, size, cracking pressure. SHCV2 is the series. S is the tube fitting end. 6 is 3/8 inch tube OD. 100P is the cracking pressure in psi. Distributors add a body material suffix, so you will also see these listed as SHCV2-S-6-100P-S316, which is the same valve.

One honest note on the 100 psi version. Superlok's published SHCV series catalog table lists cracking pressures of 1/3, 1, 5, 10 and 25 psi (0.02, 0.068, 0.34, 0.68 and 1.7 bar) and stops there. The 100 psi spring is a real part, Superlok's own North American catalog carries SHCV2-S-6-100P and distributors stock it, but it is not in that published table. So we quote 100 psi (6.9 bar) from the part number and the catalog listing rather than claiming it is in the series pressure table, because it is not.

Seal options and what they cost you in temperature

Seal Temperature range
Viton FKM, standard -10 F to 375 F (-23 C to 190 C)
Ethylene propylene, EPDM -50 F to 300 F (-45 C to 148 C)
Nitrile, NBR -10 F to 250 F (-23 C to 121 C)

The valves on this page are the FKM build. Since this is final stock, what is on the shelf is what there is, so ask before you order if you need the cold end.

Fitment

  • Fits 3/8 inch OD tube, Superlok tube fitting both ends. Flow is one way, so it has to go in the right way round.
  • Does not fit tri-clamp, NPT or hose ends, and it is not a relief valve. A check valve stops reverse flow. A relief valve protects against overpressure. They are not interchangeable.
  • Tube and spare nut and ferrule sets are separate items.
  • Not sure which set point your line needs? Call 541-330-6409 during shop hours.

$59.95 each, priced on this page. Final stock. Ships from Bend, Oregon.

View full details
Superlok 3/8" Check Valve SHCV2-S-6, 1 psi and 100 psi Cracking
SHCV2-S-6-100P

Superlok 3/8" Check Valve SHCV2-S-6, 1 psi and 100 psi Cracking

$59.95$65.00IN STOCK
SELECT CRACKING PRESSURE

ABOUT THIS PART

Superlok SHCV2 series poppet check valve, 3/8 inch tube fitting both ends, 316 stainless, spring-loaded poppet, straight-through flow path. Two fixed cracking pressures on this page, 1 psi (0.07 bar) and 100 psi (6.9 bar). $59.95 each, either one.

SPECIFICATIONS

TypePoppet check valve, one-way flow
AvailabilityCLEARANCE, final stock, not being restocked
ManufacturerSuperlok
SeriesSHCV2
Part numbersSHCV2-S-6-1P and SHCV2-S-6-100P
Size3/8 in. tube OD, Superlok tube fitting both ends
Cracking pressureFixed, not adjustable. 1 psi (0.07 bar) or 100 psi (6.9 bar)
Maximum working pressure6,000 psig (413 bar), SHCV2 with tube fitting ends
Cv1.8
Inlet and outlet body316 stainless
PoppetViton bonded to 316 stainless
Poppet stopper316 stainless
Spring304 stainless
O-ring, standardViton, fluorocarbon FKM
Backup ringPTFE
Temperature range, FKM-10 F to 375 F (-23 C to 190 C)
Seal option, EPDM-50 F to 300 F (-45 C to 148 C)
Seal option, NBR-10 F to 250 F (-23 C to 121 C)
Minimum reseal pressure, 1 psi version5 psig (0.34 bar), per Superlok's part data for SHCV2-S-6-1P
MechanismSpring-loaded poppet, straight-through flow path
Flow directionOne way. Install in the direction of flow
Price$59.95 each, either set point
Mid-range alternativeSwagelok SS-CHS6-25, same 3/8 in. size, 25 psig (1.8 bar) cracking
Not includedTube, and spare nut and ferrule sets
Built or stockedFinal stock in Bend

Both are 6,000 psig (413 bar) maximum working pressure with a Cv of 1.8. Same valve, same body, same seals. The only difference between them is the spring, and the spring is the whole decision.

Final stock, not being restocked. These came off our own shelf and there is no reorder behind them. When they are gone this listing goes with them. Priced below every distributor listing we could find in October 2026, where the same two part numbers were $62.99 each against a $81.38 published regular price.

Which cracking pressure

Set point Part number Use it when
1 psi (0.07 bar) SHCV2-S-6-1P You want flow to start almost immediately and you only need the valve to stop reverse flow. Vapor paths, vent lines, pump discharge, anywhere a stiff spring would cost you flow you cannot spare.
100 psi (6.9 bar) SHCV2-S-6-100P The valve has to stay firmly shut until the system is genuinely up to pressure. Wrong anywhere you want flow to start early or on a low-pressure vapor path.

Put a 1 psi valve in a 100 psi position and it will pass when you did not want it to. Put a 100 psi valve in a 1 psi position and it will not open when you need it to. Read the number on the part you are replacing, not the picture. If you want something in between, Superlok publishes 5, 10 and 25 psi (0.34, 0.68 and 1.7 bar) springs in this same series, and we stock the Swagelok SS-CHS6-25 at 25 psig (1.8 bar) in the same 3/8 inch size.

Specifications, from the Superlok SHCV series catalog

Series SHCV2
Part numbers on this page SHCV2-S-6-1P and SHCV2-S-6-100P
Tube size 3/8 in. tube OD, Superlok tube fitting both ends
Cracking pressure Fixed, not adjustable. 1 psi (0.07 bar) or 100 psi (6.9 bar)
Maximum working pressure 6,000 psig (413 bar), SHCV2 with tube fitting ends
Cv 1.8
Inlet and outlet body 316 stainless
Poppet Viton bonded to 316 stainless
Poppet stopper 316 stainless
Spring 304 stainless
O-ring, standard Viton, fluorocarbon FKM
Backup ring PTFE
Temperature range, FKM seal -10 F to 375 F (-23 C to 190 C)
Minimum reseal pressure, 1 psi version 5 psig (0.34 bar), per Superlok's part data for SHCV2-S-6-1P
Mechanism Spring-loaded poppet, straight-through flow path, one way
Availability Clearance, final stock, not being restocked
Price $59.95 each, either set point

What the part number says

SHCV2-S-6-100P reads left to right as series, end connection, size, cracking pressure. SHCV2 is the series. S is the tube fitting end. 6 is 3/8 inch tube OD. 100P is the cracking pressure in psi. Distributors add a body material suffix, so you will also see these listed as SHCV2-S-6-100P-S316, which is the same valve.

One honest note on the 100 psi version. Superlok's published SHCV series catalog table lists cracking pressures of 1/3, 1, 5, 10 and 25 psi (0.02, 0.068, 0.34, 0.68 and 1.7 bar) and stops there. The 100 psi spring is a real part, Superlok's own North American catalog carries SHCV2-S-6-100P and distributors stock it, but it is not in that published table. So we quote 100 psi (6.9 bar) from the part number and the catalog listing rather than claiming it is in the series pressure table, because it is not.

Seal options and what they cost you in temperature

Seal Temperature range
Viton FKM, standard -10 F to 375 F (-23 C to 190 C)
Ethylene propylene, EPDM -50 F to 300 F (-45 C to 148 C)
Nitrile, NBR -10 F to 250 F (-23 C to 121 C)

The valves on this page are the FKM build. Since this is final stock, what is on the shelf is what there is, so ask before you order if you need the cold end.

Fitment

  • Fits 3/8 inch OD tube, Superlok tube fitting both ends. Flow is one way, so it has to go in the right way round.
  • Does not fit tri-clamp, NPT or hose ends, and it is not a relief valve. A check valve stops reverse flow. A relief valve protects against overpressure. They are not interchangeable.
  • Tube and spare nut and ferrule sets are separate items.
  • Not sure which set point your line needs? Call 541-330-6409 during shop hours.

$59.95 each, priced on this page. Final stock. Ships from Bend, Oregon.

FITSCLEARANCE, final stock, not being restocked. Fits 3/8 inch OD tube, Superlok tube fitting both ends, on instrument and process lines that need one-way flow. Two fixed set points on this page, 1 psi (0.07 bar) and 100 psi (6.9 bar), and they are not interchangeable with each other. It does not fit tri-clamp, NPT or hose ends, it is not a relief valve, and it is directional so it has to be installed the right way round. For 25 psig (1.8 bar) cracking in the same size, use the Swagelok SS-CHS6-25.

▦ IN YOUR MANUAL

This part appears in the operator manual that ships with your system. The QR code there links to this page.

◈ REFERENCE FOR THIS PART

Chemical Compatibility: Seals, Gaskets and Stainless →
FKM, EPDM and NBR against your solvent, which is the seal decision on this valve
Stainless Steel: 304, 316 and 316L →
The 316 body and the 304 spring in this valve, and why the grade is proven on paper
Stainless Tubing Burst and Working Pressure Chart →
What the 3/8 in. tube either side of this valve is rated to
Certifications and Compliance →
How components on N.B. Oler builds get certified
Superlok SHCV series check valve catalog, published data
maximum working pressure, Cv 1.8, materials of construction, seal temperature ranges and the published crac...

COMMON QUESTIONS

What is the difference between the two?

Only the spring. Same body, same seals, same 6,000 psig (413 bar) rating, same Cv of 1.8. The 1P cracks at 1 psi (0.07 bar) and the 100P cracks at 100 psi (6.9 bar).

Which one do I need?

Match the valve you are replacing. 1 psi when you want flow to start almost immediately and only need to stop reverse flow. 100 psi when the valve has to stay firmly shut until the system is up to pressure. If you are not sure, call 541-330-6409.

What happens if I fit the wrong set point?

A set point that is too low will pass when you did not want it to. A set point that is too high will not open when you need it to.

Is this a clearance item?

Yes. These came off our own shelf, there is no reorder behind them, and when they are gone the listing goes.

What does the 1P or 100P mean?

It is the cracking pressure in psi, fixed, not adjustable.

Is 100 psi in Superlok's published pressure table?

No, and we will not pretend otherwise. Superlok's SHCV series catalog table lists 1/3, 1, 5, 10 and 25 psi (0.02, 0.068, 0.34, 0.68 and 1.7 bar). The 100 psi spring is a real part, carried in Superlok's own North American catalog and stocked by distributors, but it is not in that table. We quote it from the part number and the catalog listing.

What is the maximum working pressure?

6,000 psig (413 bar) for the SHCV2 with tube fitting ends. That is the valve rating, not the cracking pressure.

How cold can it go?

-10 F (-23 C) with the standard FKM seal. EPDM takes it to -50 F (-46 C) at the cost of the top end, which drops to 300 F (148 C). These are the FKM build, and since this is final stock, ask before you order if you need the cold end.

What is the Cv?

1.8.

What is it made of?

316 stainless inlet and outlet body, Viton bonded to a 316 stainless poppet, 316 stainless poppet stopper, 304 stainless spring, Viton FKM O-ring, PTFE backup ring.

Does it matter which way round I fit it?

Yes. It is a one-way valve. Fit it in the direction of flow.

Is this a relief valve?

No. A check valve stops reverse flow. A relief valve protects against overpressure. They are not interchangeable.

Is there a 25 psi option?

Yes, the Swagelok SS-CHS6-25 in the same 3/8 inch size. Superlok also publish 5 and 10 psi springs in this series, but we do not have those on the shelf.

What does it cost?

$59.95 each, either set point, priced on this page.