Skip to product information
1 of 3

Swagelok

Swagelok 1/2" Needle Valve, 316 Stainless Vee Stem, Liquid CO2 Inlet

Swagelok 1/2" Needle Valve, 316 Stainless Vee Stem, Liquid CO2 Inlet

Regular price $184.95 USD
Regular price Sale price $184.95 USD
Sale Sold out
Taxes included. Shipping calculated at checkout.
Quantity

The needle valve on the liquid CO2 inlet of every N.B. Oler hydrocarbon system. Swagelok integral bonnet needle valve, vee stem, 316 stainless body and stem tip, 1/2 inch Swagelok tube fitting both ends, 5,000 psig at 100 °F (345 bar at 38 °C). $184.95, 8 on the shelf in Bend.

Why this valve

  • The vee stem is the reason. Metering liquid CO2 into a jacket or a condenser needs fine, repeatable control near the closed position, not on and off in a quarter turn. The vee notch puts the resolution where you actually use it.
  • It is named in our certification paperwork. 3P Certz engineering reports ECR-200014-R2, the 20 LB hydrocarbon system released 23 September 2021, and ECR-200023-R0, the 40 LB hydrocarbon system released 24 August 2020, both list this valve. See certifications and compliance.
  • We do not stock a Superlok needle valve. This is the Swagelok part we buy for this job.

Where it goes on your system

  • The liquid CO2 inlet is 1/2 inch on every system we build, in every size of machine, so this is the valve.
  • It is also the inlet needle valve on our drop-in tube in shell condenser.
  • Older machine with a 3/8 inch needle valve on the LCO2 inlet? That is a legacy build and we no longer supply the 3/8 inch. Call 541-330-6409 and we will tell you what it takes to move that inlet to 1/2 inch.

Specifications, as Swagelok publishes them

Body material 316 stainless steel
Stem Vee, 316 stainless stem tip
Bonnet Integral
End connections 1/2 in. Swagelok tube fitting, both ends
Flow pattern Straight, two way
Cv 0.73
Orifice 0.250 in (6.35 mm)
Maximum working pressure 5,000 psig at 100 °F (345 bar at 38 °C)
Rating at temperature 3,435 psig at 450 °F (237 bar at 232 °C)
Temperature range -65 °F to 450 °F (-54 °C to 232 °C)
Price $184.95

The two numbers that matter on an LCO2 inlet

  • 5,000 psig at 100 °F (345 bar at 38 °C) is a wide margin over a CO2 dewar, which typically hands you around 250 psi (17.2 bar).
  • -65 °F (-54 °C) is below the temperature liquid CO2 reaches as it expands, which is the condition that stiffens or cracks a valve not rated for it.

How we buy them

Through our fitting distributor, and we take genuine new old stock when we find it, because the valve has not changed and unused inventory is unused inventory. What we do not do is substitute a look-alike. Counterfeit and gray market fittings are a real problem in this trade, and an LCO2 inlet at 5,000 psig (345 bar) is not the place to find out.

What it is not

  • Not a shutoff. A needle valve is for metering, and using it as a daily isolation valve wears the seat. Use a ball valve for isolation.
  • Not a relief valve.
  • Not a tri-clamp component. It is a tube fitting valve, so you need 1/2 inch tube and a nut and ferrule set on each side, or an adapter. None of those are included.

$184.95 each, 8 on the shelf, shipping from Bend, Oregon. Price on the page, no quote request. If we run out, allow a couple of weeks.

View full details
Swagelok 1/2" Needle Valve, 316 Stainless Vee Stem, Liquid CO2 Inlet
NB-NV-SW-12

Swagelok 1/2" Needle Valve, 316 Stainless Vee Stem, Liquid CO2 Inlet

$184.95IN STOCK

ABOUT THIS PART

The needle valve on the liquid CO2 inlet of every N.B. Oler hydrocarbon system. Swagelok integral bonnet needle valve, vee stem, 316 stainless body and stem tip, 1/2 inch Swagelok tube fitting both ends, 5,000 psig at 100 °F (345 bar at 38 °C). $184.95, 8 on the shelf in Bend.

SPECIFICATIONS

TypeIntegral bonnet needle valve, straight two way
BrandSwagelok, genuine
Manufacturer part numberSS-1VS8
Position on our systemsThe liquid CO2 inlet valve. 1/2 in on every N.B. Oler hydrocarbon system, every size
Also used onThe inlet of our drop in tube in shell condenser
Named in certification3P Certz engineering reports ECR-200014-R2 (20 LB hydrocarbon) and ECR-200023-R0 (40 LB hydrocarbon)
Body material316 stainless steel
StemVee stem, 316 stainless stem tip
BonnetIntegral
End connections1/2 in Swagelok tube fitting, both ends
Flow coefficient, Cv0.73
Orifice0.250 in (6.35 mm)
Maximum working pressure5,000 psig at 100 F (345 bar at 38 C)
Maximum working pressure at temperature3,435 psig at 450 F (237 bar at 232 C)
Temperature range-65 F to 450 F (-54 C to 232 C)
Price$184.95
Stock8 on the shelf in Bend
Lead timeA couple of weeks if we are out
Why Swagelok hereWe do not stock a Superlok needle valve. This is the Swagelok part we buy for this job
SourcingBought through our fitting distributor, plus genuine new old stock when we find it. No substitutes, no gray market
Not includedTube, nuts and ferrule sets, adapters
Not suitable asAn isolation or shutoff valve. Use a ball valve for that

Why this valve

  • The vee stem is the reason. Metering liquid CO2 into a jacket or a condenser needs fine, repeatable control near the closed position, not on and off in a quarter turn. The vee notch puts the resolution where you actually use it.
  • It is named in our certification paperwork. 3P Certz engineering reports ECR-200014-R2, the 20 LB hydrocarbon system released 23 September 2021, and ECR-200023-R0, the 40 LB hydrocarbon system released 24 August 2020, both list this valve. See certifications and compliance.
  • We do not stock a Superlok needle valve. This is the Swagelok part we buy for this job.

Where it goes on your system

  • The liquid CO2 inlet is 1/2 inch on every system we build, in every size of machine, so this is the valve.
  • It is also the inlet needle valve on our drop-in tube in shell condenser.
  • Older machine with a 3/8 inch needle valve on the LCO2 inlet? That is a legacy build and we no longer supply the 3/8 inch. Call 541-330-6409 and we will tell you what it takes to move that inlet to 1/2 inch.

Specifications, as Swagelok publishes them

Body material 316 stainless steel
Stem Vee, 316 stainless stem tip
Bonnet Integral
End connections 1/2 in. Swagelok tube fitting, both ends
Flow pattern Straight, two way
Cv 0.73
Orifice 0.250 in (6.35 mm)
Maximum working pressure 5,000 psig at 100 °F (345 bar at 38 °C)
Rating at temperature 3,435 psig at 450 °F (237 bar at 232 °C)
Temperature range -65 °F to 450 °F (-54 °C to 232 °C)
Price $184.95

The two numbers that matter on an LCO2 inlet

  • 5,000 psig at 100 °F (345 bar at 38 °C) is a wide margin over a CO2 dewar, which typically hands you around 250 psi (17.2 bar).
  • -65 °F (-54 °C) is below the temperature liquid CO2 reaches as it expands, which is the condition that stiffens or cracks a valve not rated for it.

How we buy them

Through our fitting distributor, and we take genuine new old stock when we find it, because the valve has not changed and unused inventory is unused inventory. What we do not do is substitute a look-alike. Counterfeit and gray market fittings are a real problem in this trade, and an LCO2 inlet at 5,000 psig (345 bar) is not the place to find out.

What it is not

  • Not a shutoff. A needle valve is for metering, and using it as a daily isolation valve wears the seat. Use a ball valve for isolation.
  • Not a relief valve.
  • Not a tri-clamp component. It is a tube fitting valve, so you need 1/2 inch tube and a nut and ferrule set on each side, or an adapter. None of those are included.

$184.95 each, 8 on the shelf, shipping from Bend, Oregon. Price on the page, no quote request. If we run out, allow a couple of weeks.

FITSFits the liquid CO2 inlet on every N.B. Oler hydrocarbon extraction system, in every size, because that inlet is 1/2 inch across the whole line. Also fits the inlet of our drop in tube in shell condenser. Connects with 1/2 inch Swagelok tube fittings on both ends, so it needs 1/2 inch tube and a nut and ferrule set on each side, or an adapter, none of which are included. It does NOT fit a 3/8 inch LCO2 inlet on a legacy machine, we no longer supply that size. It is not a tri-clamp component, it is not an isolation or shutoff valve, and it is not a relief valve.

▦ IN YOUR MANUAL

This part appears in the operator manual that ships with your system. The QR code there links to this page.

◈ REFERENCE FOR THIS PART

Propane and Butane Vapor Pressure Chart →
Liquid CO2 and solvent pressure against temperature on the line this valve throttles
Stainless Steel: 304, 316 and 316L →
Why this valve is 316, and how the grade gets proven on paper
Stainless Tubing Burst and Working Pressure Chart →
What the 1/2 in tube either side of this valve is rated to
Chemical Compatibility: Seals, Gaskets and Stainless →
The stem tip and seals against your solvent, and the cold end that decides it
Swagelok published product data
316 stainless body, vee stem with 316 stainless stem tip, 1/2 in Swagelok tube fitting both ends, Cv 0.73, ...
3P Certz engineering reports ECR-200014-R2 and ECR-200023-R0 →
list this needle valve on certified N.B. Oler 20 LB and 40 LB builds

COMMON QUESTIONS

What is this valve for?

Metering liquid CO2 into a jacket or a condenser. It is the needle valve on the LCO2 inlet of every N.B. Oler hydrocarbon system.

Why a needle valve instead of a ball valve?

Because you need fine, repeatable control near the closed position. A ball valve goes from nothing to everything in a quarter turn. The vee notch in this stem gives you resolution exactly where you need it on an LCO2 line.

Is it in a certification report?

Yes. 3P Certz engineering reports ECR-200014-R2, the 20 LB hydrocarbon system released 23 September 2021, and ECR-200023-R0, the 40 LB hydrocarbon system released 24 August 2020, both list this valve.

Why Swagelok when you use Superlok everywhere else?

Because we do not stock a Superlok needle valve. This is the Swagelok part we buy for this job, and it is here because it is the right valve for it.

What size do I need?

1/2 inch. The liquid CO2 inlet is 1/2 inch on every system we build, in every size of machine.

My machine has a 3/8 inch needle valve on the LCO2 inlet.

That is a legacy build. We no longer supply the 3/8 inch. Call us and we will tell you what it takes to move that inlet to 1/2 inch.

What pressure is it rated for?

5,000 psig at 100 F (345 bar at 38 C), and 3,435 psig at 450 F (237 bar at 232 C). A CO2 dewar typically supplies around 250 psi (17.2 bar), so the margin is wide.

How cold can it go?

-65 F (-54 C). That matters, because liquid CO2 gets cold as it expands and a valve not rated for it will stiffen or crack.

What is the Cv?

0.73, on a 0.250 inch (6.35 mm) orifice.

What is it made of?

316 stainless steel body with a 316 stainless vee stem tip and an integral bonnet.

Does it come with tube nuts and ferrules?

No. It is a tube fitting valve, so you need 1/2 inch tube and a nut and ferrule set on each side, or an adapter. We sell nut and ferrule sets separately.

Can I use it as a shutoff?

It will close, but that is not what it is for. A needle valve used as a daily isolation valve wears the seat. Use a ball valve for isolation.

Is it genuine Swagelok?

Yes. We buy through our fitting distributor and sometimes take genuine new old stock, which is unused inventory of an unchanged part. We do not substitute look alikes. Counterfeit and gray market fittings are a real problem in this trade and an LCO2 inlet is not where you want to find out.

How many do you have?

8 on the shelf in Bend right now.

Why is the price on the page?

Because that is how we sell everything. No quote request, no call for pricing.